Programmer:	BeeProg3	IC WRITER:	BeeProg3
IC COPIER:	BeeProg3

BeeProg3
(ord.no. 60-0061)

Ultra speed universal 64-pindrive programmer, 
design focused on high-capacity memories programming.

Short description:

• the BeeProg3 was designed meticulously with attention to details, quality and reliability
• the programmer perfectly fits for high-demanding desktop programming, as well as for automated programming systems
• based on a state of the art FPGA design, powerful ARM processor and internal SSD, the BeeProg3 is ready to program devices at theoretically possible speeds
• 64-pins rich-features, precise and powerful pindriver provides programming signals for every technology of programmable devices
• logic signals frequency up to 125MHz at 3.3V and 80MHz at 5V
• it supports devices with VCC voltages as low as 0.8V
• ultra fast programming speed, one of the fastest programmers worldwide. Sustainable programming speed greater than 31 MBytes per second
• the 8 GB eMMC NAND Flash could be done in less than 250 sec, if supported memory is fast enough
• it utilizes both universal programming modules, dedicated for IC package type and specialized modules, designed optimized for specific device families
• ESD protection on each pin of the pindriver
• dual connection to the PC: USB (2.0 HighSpeed) and LAN (100 Mbit)
• comfortable and easy to use control program, works with all versions of MS Windows from Windows XP to Windows 10 (32-bit and 64-bit)
• unique quick reaction to customer's needs - software update can be ready within a day from request, by OnDemand software
• Multiprogramming possible by attaching more programmers to one PC
• developed and made in Slovakia
• warranty - 3 years
• approved by CE laboratory to meet CE requirements
  

HARDWARE

• The 64-pin rich-features, precise and powerful pindriver of BeeProg3 deliver high speed, accurate and clean waveform signals to the device by eliminating noise, ground bounce and overshoot, which maximizes programming yield and guarantees long data retention. This also allows the reliable support of virtually any nonvolatile technology used for programmable devices - (E)EPROM, Flash, MRAM, PCM, ... - by a single device programmer.
• FPGA based totally reconfigurable TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of the device. The dual H/L drivers enables to provide two different H levels for both core signals and I/O signals of programmed device without additional logic. Programmer pindrivers operate down to 0.8V, therefore the programmer is ready to program the full range of today's and tomorrow's advanced very-low-voltage devices.
• Extremely fast programming, achieved by using FPGA based state machine, fast processor and SSD, allow execution of all time-critical routines and data transfers inside of the programmer.
• The programmer performs device insertion test based on the check of proper signal path between the programmer and programmed device before it programs each device. In dependence on programming configuration it identifies missed or poor contact between programmed device and the ZIF socket of the programming module, missed or poor contact between the programming module and the programmer and it's also able to indicate wrong position of device in the ZIF socket or the programming module (moved, rotated, backward oriented). These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
• The selftest capability allows to run the diagnostic part of software to thoroughly check the health of the programmer.
• Built-in protection circuits eliminate damage of programmer and/or programmed device due to environment or operator failure. All the inputs of the BeeProg3 programmer, including the pindriver signals, connection to PC and power supply input, are protected against ESD up to 15kV.
• Banana jack for ESD wrist straps connection to easy-to-implement the ESD protection control.
• The programming modules are available for devices in PDIP, PLCC, JLCC, SOIC, SDIP, SOP, PSOP, SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA, EBGA, FBGA, VFBGA, UBGA, FTBGA, LAP, CSP, SCSP, LQFP, MQFP, HVQFN, QLP, QIP and other packages.

Device support

Programmer, using programming modules:

• NAND FLASH: Samsung K9xxx, KFxxx, SK Hynix (ex Hynix) HY27xxx, H27xxx, Toshiba TC58xxx, TH58xxx, Micron MT29Fxxx, (ex Numonyx ex STM) NANDxxx, Spansion S30Mxxx, S34xxx, 3D-Plus 3DFNxxx, ATO Solution AFNDxxx, Fidelix FMNDxxx, Eon Silicon Sol. EN27xxx, ESMT F59xxx, LBA-NAND Toshiba THGVNxxx
• serial NAND FLASH: Micron MT29Fxxx, GigaDevice GD5Fxxx
• eMMC: Hynix H26Mxxxxxxxx, Kingston KE44B-xxxx/xxx, Micron MTFCxxxxxx, Numonyx NANDxxxxxxxx, Phison PSM4A11-xx, Samsung KLMxxxxxxx, SanDisk SDINxxx-xx, Toshiba THGBMxxxxxxxxxx
• eMCP: eMMC+RAM
• Memory Cards: MMC, SD, SDHC, SDXC
• Multi-chip devices: NAND+RAM, NOR+RAM, NOR+NOR+RAM, NAND+NOR+RAM
• Serial Flash: standard SPI, high performance Dual I/O SPI and Quad I/O SPI (25Bxxx, 25Dxxx, 25Exxx, 25Fxxx, 25Lxxx, 25Mxxx, 25Pxxx, 25Qxxx, 25Sxxx, 25Txxx, 25Uxxx, 25Vxxx, 25Wxxx, 25Xxxx, 26Vxxx, 45PExx, MX66Lxxx, S70FLxxx), DataFlash (AT45Dxxx, AT26Dxxx)
• parallel NOR Flash: 28Fxxx, 29Cxxx, 29Fxxx, 29GLxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, Samsung's K8Fxxxx, K8Cxxxx, K8Sxxxx, K8Pxxxx series, ...
• Serial E(E)PROM: Serial E(E)PROM: 11LCxxx, 24Cxxx, 24Fxxx, 25Cxxx, 30TSExxx, 34Cxxx, 34TSxx, 59Cxxx, 85xxx, 93Cxxx, NVM3060, MDAxxx series, full support for LV series, AT88SCxxx
• Serial FRAM: Cypress(Ramtron): FM24xxxxxx, FM25xxxxxx, Fujitsu: MB85RCxxxx, MB85RSxxxx, Lapis(OKI, Rohm): MR44xxxxx, MR45xxxxx
• Configuration (EE)PROM: XCFxxx, XC17xxxx, XC18Vxxx, EPCxxx, EPCSxxx, AT17xxx, AT18Fxxx, 37LVxx
• PLD Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX7000AE, MAXII/G/Z, MAX V
• PLD Lattice: ispGAL22V10x, ispLSI1xxx, ispLSI1xxxEA, ispLSI2xxx, ispLSI2xxxA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, LC4xxxB/C/V/ZC/ZE, M4-xx/xx, M4A3-xx/xx, M4A5-xx/xx, M4LV-xx/xx, ispCLOCK, Power Manager/II, ProcessorPM
• PLD Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
• SPLD/CPLD series: AMD, AMI, Atmel, Cypress, Gould, ICT, Lattice, National Semicond., Philips, STMicroelectronics, TI (TMS), Vantis, VLSI
• FPGA: Lattice: MachXO, MachXO2, LatticeXP, LatticeXP2, ispXPGA
• FPGA: Microsemi(Actel): ProASIC3, IGLOO, Fusion, ProASICplus, SmartFusion
• Microcontrollers Atmel ARM AT91SAM7Sxx, AT91SAM7Lxx, AT91SAM7Xxx, AT91SAM7XCxx, AT91SAM7SExx series;
• Microcontrollers Atmel ARM9: AT91SAM9xxx series;
• Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
• Microcontrollers Motorola/Freescale: S12, MCF52 series (ColdFire), MC56F, Kinetis (K,L), Qorivva/5xxx Power Architecture
• Microcontrollers NEC: uPD70Fxxx, uPD78Fxxx series
• Microcontrollers Nordic Semiconductor: nRF24LExxx, nRF24LUxxx, nRF315xx, nRF51xxx Flash and OTP series
• Microcontrollers Nuvoton ARM Cortex-Mx: NUC1xx, NUC2xx, M05x, Mini51, Nano1xx series
• Microcontrollers Nuvoton (Winbond): N79xxx, W77xxx, W78xxx, W79xxx, W83xxx series
• Microcontrollers NXP (Philips) UOC series: UOCIII, UOC-TOP, UOC-Fighter (TDA1xxxx) series
• Microcontrollers Renesas: R8C/Tiny series, RX series, uPD70Fxxx, uPD78Fxxx series, RL78 series, R32C series
• Microcontrollers Silicon Laboratories(Energy Micro): EFM32Gxx, EFM32GGxx, EFM32LGxx, EFM32TGxx, EFM32WGxx series
• Microcontrollers Silicon Laboratories: SiM3Cxxx, SiM3Lxxx, SiM3Uxxx series
• Microcontrollers STM (ex SGS-Thomson): SPC5 (Power Architecture)
• Microcontrollers TI (Chipcon): CC11xx, CC24xx, CC25xx, CC85xx series
• .
• --- we're currently working on the supportof devices mentioned below this line ---
• .
• EPROM: NMOS/CMOS, 27xxx and 27Cxxx series
• EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, 3D Plus 3DEExxxxxxxx
• FRAM: Ramtron
• MRAM: Everspin MRxxxxx8x, 3D Plus 3DMRxxxxxxxx
• NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD U63x series
• mDOC H3: SanDisk (ex M-Systems) SDED5xxx, SDED7xxx, MD2533xxx, MD2534xxx, Hynix HY23xxx
• Serial MRAM: Everspin MH20xxx, MH25xxx
• 1-Wire E(E)PROM: DS1xxx, DS2xxx
• FPGA: Xilinx: Spartan-3AN
• Clocks: TI(TMS), Cypress
• Special chips: Atmel Tire Pressure Monitoring ATA6285N, ATA6286N; PWM controllers: Zilker Labs, Analog Devices; Multi-Phase ICs: IR(Chil Semiconductor); Gamma buffers: AUO, Maxim, TI, ...
• Microcontrollers MCS51 series: 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx, 89Fxxx, 89LVxxx, 89LSxxx, 89LPxxx, 89Exxx, 89Lxxx, all manufacturers, Philips LPC series
• Microcontrollers ARM Cortex-M3: ATSAM3Axxx, ATSAM3Uxxx, ATSAM3Nxxx, ATSAM3Sxxx, ATSAMD20, ATSAM3Xxxx series
• Microcontrollers ARM Cortex-M4: ATSAM4Sxxx series
• Microcontrollers Atmel AVR 8bit/16bit: AT90Sxxxx, AT90pwm, AT90can, AT90usb, ATtiny, ATmega, ATxmega series
• Microcontrollers Atmel AVR32: AT32UC3xxxx, ATUCxxxD3/D4/L3U/L4U series
• Microcontrollers Coreriver: Atom 1.0, MiDAS1.0, 1.1, 2.0, 2.1, 2.2, 3.0 series
• Microcontrollers Cypress: CY7Cxxxxx, CY8Cxxxxx
• Microcontrollers ELAN: EM78Pxxx
• Microcontrollers EPSON: S1C17 series
• Microcontrollers Explore Microelectronic: EPF01x, EPF02x series
• Microcontrollers Generalplus: GPM8Fxxx series
• Microcontrollers GreenPeak: GPxxx series
• Microcontrollers Infineon(Siemens): XC800, C500, XC166, C166 series
• Microcontrollers MDT 1xxx and 2xxx series
• Microcontrollers Megawin: MG87xxx, MPC82xxx series
• Microcontrollers Motorola/Freescale: HC05, HC08, HC11, HC12, HCS08, RS08, S12X, MCF51
• Microcontrollers Myson MTV2xx, 3xx, 4xx, 5xx, CS89xx series
• Microcontrollers National: COP8xxx series
• Microcontrollers Novatek: NT68xxx series
• Microcontrollers NXP (Philips) ARM Cortex-Mx: LPC11xx, LPC11Cxx, LPC11Dxx, LPC11Uxx, LPC12xx, LPC12Dxx, LPC13xx, LPC17xx, LPC11Axx, LPC11Exx, LPC11xxLV, LPC18xx, LPC43xx, LPC8xx, EM7xx, series
• Microcontrollers NXP (Philips) ARM7: LPC2xxx, MPT6xx, PCD807xx, SAF7780xxx series
• Microcontrollers NXP (Philips) ARM9: LPC31xx series
• Microcontrollers SyncMOS: SM39xxx, SM59xxx, SM73xxx, SM79xxx, SM89xxx series
• Microcontrollers STM (ex SGS-Thomson): ST6xx, ST7xx, ST10xx, STR7xx, STR9xx, STM32F/L/W, STM8A/S/L series
• Microcontrollers Silicon Laboratories(Cygnal): C8051 series
• Microcontrollers Texas Instruments: MSP430 series, MSC12xx series, TMS320F series, CC430 series,
• Microcontrollers Texas Instruments (ex Luminary Micro): LM3Sxxx, LM3Sxxxx series, LM4Fxxxx series, TM4C series
• Microcontrollers ZILOG: Z86/Z89xxx and Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx, ZGP323xxxxxx, ZLF645xxxxxxx, ZLP12840xxxxx, ZLP323xxxxxxx series
• Microcontrollers other: EM Microelectronic, Spansion(Fujitsu), Goal Semiconductor, Hitachi, Holtek, Novatek, Macronix, Princeton, Winbond, Samsung, Toshiba, Mitsubishi, Realtek, M-Square, ASP, Coreriver, Gencore, EXODUS Microelectronic, Topro, TinyARM, VersaChips, SunplusIT, M-Square, QIXIN, Signetic, Tekmos, Weltrend, Amic, Cyrod Technologies, Ember, Ramtron, Nordic Semiconductor, Samsung, ABOV Semiconductor...

Notes:

• for all supported devices see DEVICE LIST
• compared with other Elnec programmers, the list of BeeProg3 programmer is a bit narow, but devices support is added continuously. We're focused on the implementation of mostly used and frequenly asked chip. If you need to be implemented a device not listed in the actual device list and/or by OnDemand version of the software, remind us please, we will add the support really quickly.
  Use please AlgOR Service for that request.

 

Package support

• package support includes DIP, SDIP, PLCC, JLCC, SOIC, SOP, PSOP, SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA, EBGA, FBGA, VFBGA, UBGA, FTBGA, LAP, CSP, SCSP, LQFP, MQFP, HVQFN, QLP, QIP etc.

Programming speed

 

Notes:

• It is important to say, we always use random numbers data pattern for programming speed testing. Some our competitors use "sparse" data pattern, where only small amount of non-blank data are programmed or there are used data with only few 0 bits (FE, EF, etc.). This cheating approach can "decrease" programming time considerably. If you plan to compare, ask always which pattern they use.
• The programming speed practically doesn't depend on PC type because data for programming and main part of programming algo are stored internally inside of the programmer.
• All devices mentioned below, including both NAND Flash, are programmed at their maximal speed, the programming time can not be shorter.
• Currently exist not very much devices, where the 30+ MB/s BeeProg3 programming speed can be utilized.

Device	Size [bits]	Operation	Time
JS28F00AM29EWH (parallel NOR Flash)	4000080hx16 (1 Giga)	programming and verify	116 sec.
MT29F1G08ABAEAWP (parallel NAND Flash)	8400000hx8 (1 Giga)	programming and verify	20.6 sec.
SDIN8DE2-8G (eMMC NAND FLASH)	1D2000000hx8 (64 Giga)	programming *1	269 sec.
S25FL164K (serial Flash)	800300hx8 (64 Mega)	programming and verify	20.5 sec.
AT89LP51RD2 (microcontroller)	10000hx8	programming and verify	5.2 sec.
PIC32MX360F512L (microcontroller)	80000hx8	programming and verify	8.9 sec.
*1: Verification of programming is done by internal controller of eMMC device. The device receives a block of data plus CRC, if it all matches, the internal controller confirm the proper programming. Conditions: PC type: Core2 Duo, 3.16 GHz, 1G RAM, USB 2.0 HS, Windows 7. Version of SW: 3.09, 10/2014.

 

Package includes

• BeeProg3 programmer
• power cord (Europe / USA / Japan)
• connection cable PC-programmer, USB port
• diagnostic pod for selftest of the programmer and test of the calibration (AP3 diagnostic pod, 1x)
• programming module fixating screw (1x)
• quick start guide
• CD with software and user's manual
• calibration test report
• sticker "register your programmer" (1x)
• information leaflet "Notes about ESD" (1x)
• transport case (cardboard box)
• 

Contact Details